Educational
10/22 Takedown Suppressor: The Quiet Build That Packs Small
The cleanest way to suppress a Ruger 10/22 Takedown is to swap the factory barrel for an integrally suppressed one. The Vanquish 22 Takedown is a baffle-free precision barrel that takes supersonic ammunition and drops it below the speed of sound, which removes the sonic crack.
It keeps all the takedown function of the factory barrel, still packs in the factory Ruger backpack, and is shorter than a threaded Takedown wearing a traditional muzzle-mounted suppressor.
Why put an integrally suppressed barrel on a 10/22 Takedown?
Because a takedown exists to pack small, and a muzzle suppressor works against that. Ruger built the 10/22 Takedown to split into two halves, each under 20.25″ long, that ride in the backpack case it ships with. Assembled, the factory rifle is 37″ long.
Thread a suppressor onto a Takedown and the suppressor adds length both assembled and broken down. The Reticent 22, our lightest suppressor, is 5″ long, so the assembled rifle grows by most of that, and the barrel half no longer fits the bag with the suppressor on. You end up packing the suppressor separately and threading it on every time you set up.
An integral barrel puts the suppressor around the barrel instead of past it. Broken down in a Magpul Hunter X-22 Backpacker stock, a Vanquish 22 Takedown build measures about 19.5″, suppressor included. That’s within the factory Takedown’s 20.25″ half length, and the assembled rifle stays shorter than any threaded barrel plus muzzle suppressor. The full case for going integral on the 10/22 is in our integrally suppressed 10/22 guide.
The Vanquish 22 Takedown keeps the suppressor inside the barrel half, so the rifle still packs in the factory Ruger bag and assembles shorter than a threaded Takedown with a muzzle suppressor.
What is the Vanquish 22 Takedown barrel?
The Vanquish 22 Takedown is an integrally suppressed replacement barrel built for the Ruger 10/22 Takedown. It’s an 18″ button rifled 416R stainless barrel with a Bentz match chamber, wrapped in a 6061 aluminum shroud with a Cerakote finish.
The barrel is precision ported, which means gas bleeds off through holes along its length as the bullet speeds past them. That slows standard velocity .22LR below the speed of sound, so the Vanquish 22 Takedown quiets both the muzzle blast and the sonic crack on supersonic ammo. The physics are in our explainer on how suppressors work.
There are no baffles inside. The ports and the internal volume do the work, so there is nothing to erode, nothing to strike, and no lead stack to pick apart at cleaning time. It’s the same design as every Vanquish 22, covered in depth in our Vanquish 22 review.
| Spec | Detail |
|---|---|
| Platform | Ruger 10/22 Takedown |
| Barrel | 18″ precision ported, 416R stainless, button rifled |
| Twist | 1 in 16 |
| Chamber | Bentz match chamber |
| Contour | 0.920″ bull |
| Shroud | 6061 aluminum, Cerakote finish |
| Weight | 1.44 lb |
| Design | Baffle-free, no baffle strikes |
| Ammo | Standard velocity and subsonic .22LR; not CCI Stinger |
The Vanquish 22 Takedown is an 18″ ported, baffle-free 416R barrel with a Bentz match chamber that runs standard velocity .22LR subsonic.
What do you need for a suppressed 10/22 Takedown build?
Four parts and the ammo. The barrel is the only part that takes paperwork, and it’s the heart of the build.
| Component | What to use | Notes |
|---|---|---|
| Host | Ruger 10/22 Takedown | Any factory Takedown |
| Barrel | Vanquish 22 Takedown | The NFA item you register; move your lockup ring and adapter over |
| Stock | Magpul X-22 Backpacker or any bull-barrel takedown stock | Many factory stocks are cut for the slimmer factory barrel; Takedowns shipped with the X-22 Backpacker are ready as is |
| Optic | Red dot or low-power scope | Mount on the receiver; the lockup returns to zero |
| Ammo | Standard velocity or subsonic .22LR | No CCI Stinger |
Most owners already have the host and an optic. The two changes are the barrel and, for most factory rifles, the stock.
A suppressed 10/22 Takedown build is a factory Takedown, the Vanquish 22 Takedown barrel, a bull-barrel takedown stock like the Magpul X-22 Backpacker, an optic, and standard velocity ammo.
How do you install the Vanquish 22 Takedown barrel?
It’s a barrel swap, not a gunsmithing job. Separate the rifle, remove the takedown lockup ring and adapter from your factory barrel, and reinstall them on the Vanquish 22 Takedown. Then reassemble and set the lockup tension the same way you did with the factory barrel.
Ruger designed the Takedown’s friction-fit lockup to return to zero, even with optics mounted on the receiver, and to rarely need adjustment after the first assembly. Take the time to set it right once and it stays set.
Our install video walks through every step.
One fit note: Tactical Solutions 10/22 and Fletcher Rifle Works receivers use a barrel inlet tighter than Ruger factory spec, so the Vanquish 22 Takedown may need a little hand fitting in either. Contact us if you run into any issues during installation.
Install the Vanquish 22 Takedown by moving your factory lockup ring and adapter onto it, then setting lockup tension once. No gunsmith required.
Do you need a new stock for the Vanquish 22 Takedown?
Possibly. The Vanquish 22 Takedown has a 0.920″ bull contour, the same diameter as a Ruger 10/22 bull barrel, and many of the factory Takedown stocks are cut for the slimmer factory barrel. If your Takedown shipped with a Magpul X-22 Backpacker stock, you’re good to go. The barrel fits any takedown stock that accepts a bull barrel.
If you need to upgrade your stock, we recommend the Magpul X-22 Backpacker. It was built for the 10/22 Takedown, weighs 18.25 ounces, and carries its own gear: a hinged compartment under the comb holds three 10-round magazines or a 50-round box of .22LR, and the grip has a sealed compartment for small parts.
Some third-party stocks run tight on tolerances and may need minor hand fitting.
The Vanquish 22 Takedown fits any takedown stock that accepts a 0.920″ bull barrel. Takedowns that ship with the Magpul X-22 Backpacker are ready as is, and it’s the stock we recommend if you need to upgrade.
What ammo should you run in a suppressed 10/22 Takedown?
Standard velocity or subsonic .22LR. The Vanquish 22 Takedown already pulls standard velocity loads below the speed of sound, which is where it sounds best, so there’s no need to hunt for specialty ammo. Skip CCI Stinger: its longer case won’t fit the Bentz match chamber. Our guide to the best subsonic and standard velocity 22LR ammo has the full list.
Run standard velocity or subsonic .22LR in the Vanquish 22 Takedown, and avoid CCI Stinger, which does not fit the Bentz match chamber.
Does a suppressed 10/22 Takedown create any extra NFA issues?
No. The Vanquish 22 Takedown barrel is the NFA item, registered as a suppressor. At 18″, the barrel is over the 16″ rifle minimum, so a stocked Takedown stays a standard rifle with no short-barreled rifle question.
That’s different from the 12″ Charger barrel, where adding a stock changes the classification. Our Ruger 10/22 Charger suppressed build guide covers that case. For the paperwork on the barrel itself, here’s how to buy a suppressor from start to finish.
The Vanquish 22 Takedown barrel is one NFA item, registered as a suppressor, and at 18″ it keeps a stocked Takedown a standard rifle.
Who is this build for, and when is it the wrong choice?
Many owners run the Vanquish 22 Takedown as a range gun, a survival rifle, and an all-around backyard pest gun. It’s quiet on cheap standard velocity ammo, short to carry, and it breaks down to stow in a closet, a truck, or a pack.
It’s the wrong build if peak quiet is all you care about. On subsonic ammo, a Reticent 22 on a threaded standard Takedown meters quieter. If you want the quietest possible range gun and don’t mind the extra length or packing the suppressor separately, that’s the better setup. The Reticent 22 also moves to any 1/2×28 rimfire host, where the Vanquish 22 Takedown serves one rifle.
For the full comparison of the two approaches, see integrally suppressed vs. traditional suppressors.
Pick the Vanquish 22 Takedown for a quiet takedown that packs small. Pick a Reticent 22 on a threaded Takedown for the lowest meter reading and one suppressor across your rimfire hosts.
A quiet takedown that still packs small
The Vanquish 22 Takedown puts the suppressor inside an 18″ match-chambered barrel, so your 10/22 Takedown runs standard ammo subsonic, assembles shorter than any threaded barrel and muzzle suppressor, and still breaks down into the bag it came in.
Download the free guide now!
From bare receiver to backyard-quiet, this guide walks you through every part of a suppressed 10/22 build. Skip the guesswork, enter your email and we'll send it straight to your inbox!
Featured Products
-
Vanquish 22TD Suppressed Ruger 10/22 Takedown Barrel
Original price was: $599.00.$535.00Current price is: $535.00. -
Reticent 22 Suppressor
Original price was: $375.00.$345.00Current price is: $345.00.
Frequently asked questions
For a takedown that still packs small, an integrally suppressed barrel like the Vanquish 22 Takedown. The suppressor is built into the 18 inch barrel, so the rifle breaks down into the factory Ruger bag and runs standard velocity .22LR subsonic. For the lowest meter reading, a Reticent 22 on a threaded Takedown is quieter on subsonic ammo.
It depends on the stock. The Vanquish 22 Takedown has a 0.920 inch bull contour, and many factory Takedown stocks are cut for a slimmer barrel. Takedowns that ship with the Magpul X-22 Backpacker are ready as is. It fits any takedown stock that accepts a bull barrel. Some third-party stocks may need minor hand fitting.
Separate the rifle, remove the takedown lockup ring and adapter from the factory barrel, and reinstall them on the Vanquish 22 Takedown. Reassemble and set the lockup tension. No gunsmithing is required. Tactical Solutions and Fletcher Rifle Works receivers have a tighter barrel inlet and may need light hand fitting.
No. The Vanquish 22 Takedown is ported to drop standard velocity .22LR below the speed of sound, so ordinary ammo runs quiet. Avoid CCI Stinger, whose longer case does not fit the Bentz match chamber. Standard velocity and subsonic loads sound best.
No. The Vanquish 22 Takedown barrel is 18 inches, over the 16 inch rifle minimum, so a stocked Takedown stays a standard rifle. The barrel itself is registered as a suppressor, which is the one NFA item in the build.
Latest Intel
ATF’s NFA Open Letter: Do Suppressors Still Need to Be Registered?
Oct
10/22 Takedown Suppressor: The Quiet Build That Packs Small
Oct
Top 7 Suppressor Myths, Debunked
Oct
DOJ Won’t Appeal the NFA Ruling: What It Means for Buyers
Oct
Best Suppressor for the Ruger Mark IV
Oct
How Long Does a Rimfire Suppressor Last?
2 Comments
Sep