Traditional integrally suppressed systems have very short barrels (3″-8″) with a monocore suppressor pin and welded to the end of the barrel. This typically results in very poor accuracy, low velocity and tedious cleaning sessions. The Vanquish 22 features a fully rifled barrel (12″-18″ depending on model) and no baffle stack. This results in a barrel that is much more accurate than the factory barrel, delivers optimal velocity and almost zero cleaning maintenance in addition to being very quiet.

The Vanquish zero baffle design relies on volume to decrease sound levels. Therefore, the full length models will be quieter than the shorter length models (Charger and AR22 Short). There is no significant difference between the standard 10/22 and the Takedown version at the shooters ear

No. The internal geometry is designed to minimize oxygen in the expansion chamber, which significantly reduces first-round pop. The first shot sounds essentially the same as every other shot.

• Ruger 10/22
• Ruger 10/22 Takedown
• Ruger 10/22 Charger
• Ruger Precision Rimfire
• AR-15 with dedicated 22LR CMMG Bolt
• More models coming soon

Tactical Solutions 10/22 receivers feature an undersized barrel inlet compared to Ruger factory dimensions. This typically results in a tighter fit but may require a small amount of hand finishing for proper installation. Please contact our customer support team if you have questions on this process.

Yes. Several manufacturers offer a Vanquish equipped complete rifle including, Volquartsen Firearms, Black Rain Ordnance and Fletcher Rifle Works.

No. The Vanquish does not require subsonic ammunition to be quiet. Due to the porting system most standard velocity ammunition will drop to subsonic levels. However, you can shoot subsonic ammunition and it will be even quieter that supersonic ammunition.

Yes. The porting system bleads off just enough gas to drop most standard velocity ammunition to subsonic levels (removing the super sonic crack). Please note: factors like temperature, humidity and altitude can play a factor in sound.

Yes, the Vanquish 22 can run standard and high-velocity .22LR. Just note that high-velocity rounds may break the sound barrier, which causes the supersonic crack from the bullet itself. For the quietest performance, use standard velocity or subsonic .22LR ammunition. Please note due to the Bentz match chamber, the Vanquish 22 is not compatible with CCI Stinger hyper-velocity ammunition because the Stinger case is slightly longer at .702″ versus .613″ for a traditional 22LR case. Instead, if you want to shoot a high velocity round, we recommend the CCI Velocitor as it uses a normal case length and is still rated at 1,435 ft/sec.

The Bentz chamber is engineered as a precision-oriented chamber for semi-automatic platforms. It features tighter tolerances than a standard sporter chamber while remaining less restrictive than a true minimum-spec, match competition chamber. Due to these reduced clearances, the use of CCI® Stinger® and other extended-case hyper-velocity ammunition is not recommended. In addition, some unfired cartridges may not reliably extract.

Yes, in a positive way. Because the suppression system is integrated into the barrel instead of hanging weight off the muzzle, the rifle maintains natural balance and consistent barrel harmonics. This leads to excellent repeatability.

Simply remove the outer shroud and wipe down the barrel. Tip out any loose carbon inside the shroud. Lastly, run a bore patch down the barrel like you would any firearm. Cleaning the ports is not required after every use.

No, the Vanquish 22 does not require special armorer’s tools. The front cap is hand removable, and standard .22 cleaning tools are all that is needed for normal maintenance.

No. The Vanquish 22 barrel is only compatible with the standard configuration 10/22 rifles

The Vanquish barrel extension is built to meet Ruger Factory specifications. Some aftermarket manufacturers including Fletcher Rifle Works and Tactical Solutions feature a undersized barrel inlet and some minor hand fitting maybe required. Contact our support team if you need assistance fitting your barrel to your receiver.

Yes, it is a drop-in fit for standard Ruger 10/22 receivers and most aftermarket receivers, stocks, and chassis systems. If your setup accepts a standard 10/22 barrel, the Vanquish 22 will fit.

The Vanquish 22 is ideal for shooters who want a quiet, accurate and well balanced and compact .22 rifle — including small-game hunters, property owners, pest control, precision rimfire shooters, and anyone who prefers a clean, streamlined suppressor profile with no added length.

If you want to use a single suppressor across multiple firearms, a thread-on suppressor may be a better fit. The Vanquish 22 is purpose-built for shooters who want a dedicated .22 LR platform with integrated suppression and optimized handling.

Yes, it is legally a suppressor. One Form 4 tax stamp is required.

Approval times are faster than ever before! eForm 4 suppressor approvals are taking days on average for both individual and trust submissions

Starting January 1, 2026 you will no longer have to pay a $200 tax stamp for items regulated under the National Firearms Act (NFA), including suppressors, short-barreled rifles, and short-barreled shotguns. Any NFA items purchased before this date still require the $200 tax stamp.

You’ll submit a Form 4 through your dealer, the ATF reviews it, and once approved, your barrel is ready to take home.

Yes, suppressors do not require interstate travel notification like SBRs do. You may travel across state lines as long as the suppressor is legal in the destination state.